Hands-On with the Romain Gauthier Prestige HMS Stainless Steel

With a meteorite dial from Down Under.

The Prestige HMS was Romain Gauthier’s second wristwatch, but more importantly, it’s part of his first generation of designs, which had a more classical look as well as a “back winder” crown (as compared to the newer Insight Micro-Rotor or Logical One, for instance). Now the Prestige HMS has been facelifted with a meteorite dial and steel case, giving it a fresh appearance, while retaining the highly regarded and finely finished movement.

The new Prestige has a lighter, more modern look, helped by the pale grey tones and larger steel case. Its appeal is further boosted by the fact that it’s the first serially produced Romain Gauthier wristwatch in stainless steel, making it more affordable than equivalents in gold or platinum.

In essence, the new Prestige is an attractive middle ground between the earliest Romain Gauthier watches, which are more traditonal, and the very latest, which are sporty and contemporary.

The lineage

First introduced in 2012 with a guilloche dial and precious metal cases (titanium came slightly later), the Prestige HMS is a three-hand, time-only watch. “HMS” is short for hours, minutes and seconds; Romain Gauthier’s first model from 2006 was merely “HM”. Though functionally simple, the Prestige HMS, much like the rest of Romain Gauthier’s timepieces, is intrinsically complex in construction and finish.

The movement in Prestige models is characterised by the uncommon crown that sits flat on the case back, known as a “back wind”. Occasionally found on vintage watches, especially small lady’s timepieces, the “back winder” crown is meant to give the case an uninterrupted silhouette while allowing the wearer to wind the watch while it’s on the wrist. On the wrist, the watch feels no different from one with a conventional crown, because the “back wind” crown is almost flush with the case back.

In practice, however, the crown setup is inconvenient because of its flatness, which makes for a poor grip. A swivelling tab would make winding easier, but the new Prestige HMS keeps the flat, serrated crown.

The watch is quite a bit larger than the original Prestige watches, with the case measuring 43mm in diameter and 12.1mm in height. The case middle is brushed, while the bezel is polished. Together the larger size and contrasting surfaces give the watch a decidedly more modern look when compared to the earlier Prestige watches.

An otherworldly dial

The dial is made of a thin slice of meteorite that was discovered in 1931 at the Henbury crater field in the vast and desolate Northern Territory of Australia. Now a conservation area, the crater field contains just over a dozen craters from meteorite strikes that occurred over 4700 years ago. The dials of the Prestige HMS are the only samples of Henbury meteorite outside the South Australian Museum in Adelaide.

Like most other meteorite used for watch dials, the cosmic rock here is an octahedrite, or iron meteorite. Such meteorites are composed of over 90% iron, with the rest being nickel and small amounts of other heavy metals. A mottled grey in its natural state, meteorite is typically sliced into thin pieces and then chemically etched to accentuate the fabulously complex Widmanstätten pattern that comes from the iron and nickel crystals inside.

A sample of Henbury meteorite that’s been sliced and then etched

Each ribbon-like crystal is slightly different in composition and is weakly bonded to another, which creates a fragility that makes meteorite a nightmare to work with. Regular milling machines simply do not cut it (no pun intended), so instead the dial is made in two steps.

First with electrical discharge machining to cut out the shape, and then a three-axe CNC mill for the details like the holes for the feet of the hour markers, creating a dial that is just 0.8mm high. The dial is then coated with a corrosion-resistant lacquer to prevent the iron and nickel inside the meteorite from oxidising.

The Henbury meteorites are medium octahedrites, classified according to the fineness of the metal crystal layers inside. Consequently, the Prestige HMS dial has wider bands in its Widmanstätten pattern, resembling bold brushstrokes. In contrast, the meteorite dials found on other watches like the Omega Speedmaster Grey Side of the Moon or Jaeger-LeCoultre Master Calendar have narrower, more defined bands as they are typically obtained from the more common Gibeon meteorites of Namibia, a finer octahedrite.

The hour markers are solid gold while the hands will be blackened steel (the watch pictured has prototype hands), both filled with Super-Luminova for night-time visibility. And the hands have their tips covered in Super-Luminova, giving the watch a high degree of legibility.

Florid mechanics

Inside the watch is the same calibre 2206 found in the earlier Prestige watches, the movement that first made collectors take notice of Romain Gauthier. It’s hand-wound with a 60-hour power reserve.

The movement is indeed stunning, with fluid contours of the bridges that flow in synchrony with the gears. The volume of the bridges has also been minimised to reveal as much of the moving parts as possible. That means not only the wheel train and regulator are visible The barrel bridge has a sharply defined cut-out that offers a glimpse of the barrel and winding click, while three short finger-bridges hold the first, escape and balance wheels.

Amongst its many features, the cal. 2206 has a free-sprung, adjustable mass balance of Romain Gauthier’s own design, featuring gently curved arms. The pallet fork is also proprietary, being triangular in form for maximum rigidity that promises more stable operation.

As with all of Romain Gauthier’s movements, the appeal of the cal. 2206 lies not only in the complex forms of the bridges, but also the unusual detailing that gives the movement a subtle yet distinctive identity.

All of the going train wheels, for instance, feature circular spokes that bring to mind flower petals, while all screws have an S-shaped slot. All that is made possible by Romain Gauthier’s well-equipped production facility that also supplies other brands, including Chanel for its high-end Monsieur watch.

While the construction of the movement is the same, it is finished differently here. The bridges and main plate both have a black finish, which makes the finely executed decoration less obvious. The bridges have straight graining on their top surfaces along with polished, rounded bevels, while the base plate has a hand-frosted finish.

Price and Availability

The Prestige HMS Stainless Steel is a 10-piece limited edition priced at SFr68,000 before taxes.


 

Back to top.

You may also enjoy these.

How “Vintage” Dials are Made at Glashütte Original

Producing the brilliantly retro Sixties dials.

Watchmakers don’t often detail production processes, especially those regarded as proprietary. That’s often unfounded paranoia, since there are only so many ways to produce a watch (or a hairspring or a balance wheel).

So Glashütte Original’s latest bit of news is refreshingly enlightening and original. It details, step by step, the production of the unusual and striking dials found in the retro Sixties watches that are modelled on watches produced in the former East Germany. While the dial-making process is not unique, the stamped pattern on the Sixties dial is uncommon. Originally available as a limited edition in a variety of finishes, the Sixties is now offered with a brilliant green dial decorated with a radial pattern that evokes water droplets. And this is how it’s made.

From German silver blank (at left) to finished Sixties dial

The birth of Glashütte Original’s dial-making prowess happened in 2006, when its parent company Swatch Group acquired Th. Müller, a dial factory located in Pforzheim, the historic centre of the German jewellery and clock industry. The Scheufele family that now owns Chopard, for instance, were originally jewellers from Pforzheim, which sits just the north of the Black Forest.

Established in 1922, Th. Müller was once the biggest supplier of dials to VEB Glashütter Uhrenbetriebe (GUB), the state-owned watch factory in East Germany that was the predecessor of Glashütte Original. Renamed Deutsche Zifferblatt Manufaktur, the Th. Müller factory was relocated, expanded and upgraded by the Swatch Group, and now supplies dials to several luxury watch brands, including for much of Glashütte Original’s output.

The Glashütte Original Sixties Annual Edition 2018


Retro reprint

The process starts with a ribbon of German silver, an alloy of mostly copper with a bit of nickel and zinc that’s strong, corrosion-resistant and easy to machine. Of course the best known use of German silver, also known as maillechort or nickel silver, is for the bridges and base plate in the movements of high-end watches, most notably those of Glashütte Original’s neighbour, A. Lange & Söhne.

A smooth round disc is stamped out from the German silver strip, forming the dial blank. Then the dial pattern is stamped with a 60-tonne press dating from the 1960s. In fact, the pattern stamping is done by the same machine that decorated the dials Th. Müller supplied to GUB before the Berlin Wall fell, explaining why the modern day Sixties dial looks so convincingly retro.

Stamping out blanks

Pattern stamping complete

Next the blank has the excess around the edge trimmed off, and a hole is drilled in its centre for the cannon pinion that holds the hands. Then it undergoes a second pressing operation that gives the dial its domed shape, just like on the 1960s originals.

The domed dial on the vintage originals was to allow the movement to fit in a slimmer case, as the movements used then were quite small, some of the movement height could be accommodated by the dial.

Giving the dial its domed form

The dial, which is just 0.5mm thick, is then galvanised, given a layer of zinc plating that protects it against corrosion and oxidation. It’s then covered in several layers of green lacquer, followed by an artful application of black lacquer that results in its graduated colour that goes from bright green in the centre to black at its edges. The final step is a trip to the oven to set the lacquer and make the finish permanent.

Eight hour markers are then cut from the dial surface with a milling machine, giving the dial its distinctive recesses for the indices in-between the quarters. Because material is cut out from the dial for the indices, it reveals the metal of the German silver below.

Cutting the hour markers

The rapidly spinning diamond-tipped tool creates a clean divot for each hour marker

The Arabic numerals for the hour markers at the quarters, as well as the minute track, logo and assorted text on the dial is then applied via pad printing. A printing pad made of silicone picks up the artwork in ink and then prints it onto the dial.

And the last step is the application of glow-in-the-dark Super-Luminova – a small syringe is used to deposit a tiny sphere of Super-Luminova for each hour marker. The small process is also used to fill the hour and minute hands with “lume”.

Pad printing, also known as tampography

Lume injections

While the process above documents dial-making for last year’s Sixties Annual Edition in green, subsequent “annual editions” will feature dials produced in a similar manner, which should promise similar vintage flair.


All photos courtesy Glashütte Original

Back to top.

You may also enjoy these.

Welcome to the new Watches By SJX.

Subscribe to get the latest articles and reviews delivered to your inbox.

Exit mobile version