Up Close with the Bell & Ross BR-X2 Tourbillon Micro-Rotor

A deliciously thin sapphire sandwich with a newly developed flying tourbillon movement.

Bell & Ross typically makes affordable, military-inspired wristwatches, which it does well. When the French watchmaker made complicated watches in the past, they tended to look, well, complicated. Taking a different tack is the BR-X2 Tourbillon Micro-Rotor.

Thin and conceived to have minimal case and maximum movement, it’s fitted with panoramic sapphire crystals front and back. The thick, bevelled sapphire crystals on both faces comprise more than half of the case height, offering a free and clear view of the movement.

Bell & Ross BR-X2 Tourbillon 13

The sloping sides of both crystals are mirror-polished, enhancing their transparency and letting more light into the movement. Clear gaskets on both side sit invisibly under the crystals, giving the case a respectable 50m water-resistance without obstructing the view.

Bell & Ross BR-X2 Tourbillon 1

Bell & Ross BR-X2 Tourbillon 2

Bell & Ross BR-X2 Tourbillon 12

Bell & Ross BR-X2 Tourbillon 17

Bell & Ross BR-X2 Tourbillon 11

Rather than enclose the movement, the steel case frames it, with the movement having been constructed to fit within like a painting in a frame.  In fact, the movement and case appear almost seamless, with the narrowest of space between them.

Bell & Ross BR-X2 Tourbillon 32

Bell & Ross BR-X2 Tourbillon 33

Sleekly constructed

The BR-X2 is a large watch, measuring 42.5mm both ways, but thin at just 8.9mm high. Though it is made of steel, the case feels like titanium, since there is little of it. The short lugs allow it to sit well on the wrist, while also accentuating its size.

Bell & Ross BR-X2 Tourbillon 3

The watch is one of the thinnest tourbillon watches on the market; there are only about a half dozen tourbillon wristwatches with cases below 10mm. Most of that height, however, is sapphire crystal.

Bell & Ross BR-X2 Tourbillon 30

Bell & Ross BR-X2 Tourbillon 15

Bell & Ross BR-X2 Tourbillon 16

Bell & Ross BR-X2 Tourbillon 26

The only fancy detailing on the watch is the tourbillon cage six o’clock that takes the form of the ampersand from the Bell & Ross logo. While that’s found on all of the brand’s tourbillons, a simpler cage design would have been more congruent with the clean lines of the watch.

Bell & Ross BR-X2 Tourbillon 4

Bell & Ross BR-X2 Tourbillon 10

Extra-thin mechanics

Like the other tourbillon movements used by Bell & Ross, the BR-CAL.380 was developed by MHC Manufacture Haute Complication, a Geneva-based complications specialist formed by watchmakers from BNB Concept, a movement maker that was acquired by Hublot after going bust. Amongst other things, MHC helped build the Girard-Perregaux Tri-Axial Tourbillon.

The base plate and bridges of the BR-CAL.380 inside give it a square footprint with rounded cut-outs at each corner to accommodate the screws on the case. This allows the movement to slide neatly into the frame of the case, secured in place by four small clips on the back.

Bell & Ross BR-X2 Tourbillon 19

Measuring 36mm by 36mm, the movement is large but just 4.05mm in height. It’s self-winding with a micro-rotor made of a dense tungsten alloy on the back and a 50-hour power reserve.

Bell & Ross BR-X2 Tourbillon 14

Bell & Ross BR-X2 Tourbillon 34

The movement layout is intuitive, with the base of the winding mechanism visible on the dial at nine o’clock, while part of the gear train is visible on the back.

Fuss-free finishing

Though the watch is almost monochromatic, being almost entirely in different tones of silver, the varied surface finishing gives the colour palette nuance. Most of the movement is rhodium-plated and finished with a vertical brushed finish, though a handful of parts are sandblasted to leave a coarse, grained surface.

Bell & Ross BR-X2 Tourbillon 7

Bell & Ross BR-X2 Tourbillon 28

The contrast is obvious on the front, with the brushed base plate against the sandblasted bridge for the keyless works. And just above the base plate sits a sloping flange finished with circular brushing that holds the baton hour markers, which gently float above the dial. They are matched with frosted hour and minute hands, all of which are strongly legible.

Bell & Ross BR-X2 Tourbillon 18

Bell & Ross BR-X2 Tourbillon 9

Bell & Ross BR-X2 Tourbillon 6

Bell & Ross BR-X2 Tourbillon 5

Bell & Ross BR-X2 Tourbillon 8

Bell & Ross BR-X2 Tourbillon 27

On the back the aesthetic is identical, with vertical brushing on all flat surfaces, while bevels and recessed areas are sandblasted.

Bell & Ross BR-X2 Tourbillon 22

Bell & Ross BR-X2 Tourbillon 23

Bell & Ross BR-X2 Tourbillon 20

Bell & Ross BR-X2 Tourbillon 21

The look is crisp and functional, though smaller components are finished more decoratively. Gears, for instance, have their faces circular grained and spokes bevelled, while the tourbillon cage is brushed on top and polished on its edges. By no means artisanal, the finishing is eminently suited to the look (and price) of the watch.

Bell & Ross BR-X2 Tourbillon 24

Bell & Ross BR-X2 Tourbillon 29

Price and availability 

The BR-X2 Tourbillon Micro-Rotor (ref. BRX2-MRTB-ST) is a limited edition of 99 watches, priced at US$64,900 or S$95,000. While that’s many multiples the cost of the average Bell & Ross wristwatch, it places the BR-X2 in the mid-price tier for tourbillons, mostly alongside watches from smaller brands like Manufacture Royale and Arnold & Son.

For more on the BR-X2 Tourbillon, visit bellross.com.

Bell & Ross BR-X2 Tourbillon 25


 

Back to top.

You may also enjoy these.